- EOC-2610 is a long range outdoor wireless Access Point and Client Bridge that operates seamlessly in the 2.4GHz frequency spectrum. It features high transmitted output power and high receivable sensitivity. High output power and high sensitivity can extend range.
- Obviously the first thing you want to do is set the appropriate Target System. For the Engenius EOC-2610, you’ll want to use Atheros AR2315: Menuconfig: Selecting your Target. Next, ensure you select squashfs for the Root filesystem image (under Target Image). Target Profile will only have one option (Default), so no changes are needed there.
From DD-WRT Wiki
Sebelum mengahiri tutorial ini, perlu diketahui bahwa Senao EnGenius EOC-2610 dapat memancarkan dan menangkap frekuensi 1 - 30 kilometer dalam kondisi bersih dan stabil. Itu juga ada setingan sendiri dengan masuk ke Wireless - Wireless Advanced Setting. EnGenius 2610 / 1650 client router configuration. If you purchased on of our bridge kits you will need 2 standard straight through ethernet cables available at your local store. One cable will run from your computer to the power injector the other from the PoE side of the injector to the bridge up to 300 feet away.
SENAO EOC-2610
|
THX to malcolmchng
- Ubiquity Nanostation2 clone with better hardware.
- 600mW Wireless Power.
- 24V PoE.
- SuperG 108Mbps Support.
- Internal dual 10dBi panel.
Since many of you guys (me either) have problems with the antenna settings here are some hints to get the right ones working
[edit]Internal
The setting of the internal antenna are a bit tricky due to the fact that the correct state of the settings is REV dependent.You will have to try if secondary or primary antenne setting works better.
For Revision 1.1.13 this setting is diversity on and TX/RX to secondary.
[edit]External
In some Builds you can set the antenna to secondary in some not. If you can set it to secondary and push the hardware switch to ext. Now the rp-sma plug is active
For Revision 1.1.13 this doesnt work corrently as it continues to use the internal.To over come this you can solder RP-SMA connectors onto the internal plugs.[[Image:[1]]]
1. Download the free web server: (you are free to use any other web server that you are familiar with). http://www.ashleybrown.co.uk/downloads/iws2.exe
2. Create a folder C:test
3. Download the special V.25 only DD-WRT image from Senao server and copy DD-WRT_newimage.bin into C:testhttp://www.senao.com/images/www.senao.com_English/DD-WRT_newimage.bin?CATNO0=D&CATNO1=D3&CNT=1This image contains DD-WRT firmware; once loaded no additional porting is required.
4. Configure your PC with IP 192.168.1.11 (you can use any other IP also)
5. Start the web server by executing iws.exe and double click on the icon on your system-tray at the bottom-right corner.
6. Configure the web server with the following configuration; click OK when done.
Cara Reset Engenius Eoc 2610
Public Folder ---------> c:testDefault File ----------> index.htmlPort ------------------> 80
7. Please test the server http://192.168.1.11/ DD-WRT_newimage.bin; it may take a few seconds before the page is completely loaded by your web-browser.
8. Power on EOC-2610 and make sure it is complete booted. You can verify it by accessing its web page UI.
9. Once booted; telnet 192.168.1.1; the username & password are both “admin”
Cara Setting Engenius Eoc 2610 User
10. Under the console prompt type in the following commands in REDtogether with the address link
IMPORTANT: Please note that never interrupt the last command (cat …) under any circumstance (make sure the power is table and do not touch anything during the 3~10 minutes write process). It will cause incomplete write on the flash and make it unbootable. Do not mis-type anything!
Enjoy!!
